all said and done

BaseLeft.scad

@@ -15,13 +15,13 @@ module through(l=7, lh=3.3, lt=1, lb=1){
 }
 
 module m3 (h=8, lb=1){
-    translate([0,0,-lb])cylinder(h+lb, d=2.5); // tapped M3
-    //translate([0,0,-lb])cylinder(h+lb, d=4); // rutex insert
+    //translate([0,0,-lb])cylinder(h+lb, d=2.5); // tapped M3
+    translate([0,0,-lb])cylinder(h+lb, d=4); // rutex insert
 }
 
 module m2 (h=8, lt=1){
-    translate([0,0,-lt])cylinder(h, d=1.5); // tapped M3
-    //translate([0,0,-lt])cylinder(h, d=3.2); // rutex insert
+    //translate([0,0,-lt])cylinder(h, d=1.5); // tapped M3
+    translate([0,0,-lt])cylinder(h, d=3.2); // rutex insert
 }
 
 difference(){

BaseRight.scad

@@ -15,8 +15,8 @@ module through(l=7, lh=3.3, lt=1, lb=1){
 }
 
 module m3 (h=8, lb=1){
-    translate([0,0,-lb])cylinder(h+lb, d=2.5); // tapped M3
-    //translate([0,0,-lb])cylinder(h+lb, d=4); // rutex insert
+    //translate([0,0,-lb])cylinder(h+lb, d=2.5); // tapped M3
+    translate([0,0,-lb])cylinder(h+lb, d=4); // rutex insert
 }
 
 difference(){

coolingFanDuct.scad

@@ -10,8 +10,8 @@ yhbl = -15.5; // distance in y from fan center to center of nozzle (negative to
 zhbl = 27.2; // distance in z from fan to heat block underside
 zbed = 6.5; // how far does the nozzle protrude out of the heat block?
 xhbln = 11.5; // distance from heat block to nozzle center
-zgap = 2; // gap left to bed/part
-xgap = 3; // gap from duct to heat block
+zgap = 2.5; // gap left to bed/part
+xgap = 4; // gap from duct to heat block
 
 
 /* fan size */
@@ -114,5 +114,6 @@ difference(){
     translate([-1,y-bpt-0.4,-zofsmnt])cube([xto*2,bpt+1,zofsmnt+1]);
 
     // cut view
+
  //translate([-1,-1,-zhbl-zbed])cube([xto+xhbl+2,lf/2,zhbl+zbed+5]);
 }

coolingFanMount.scad

@@ -34,12 +34,12 @@ module m2 (h=8, lt=1){
 }
 
 module mount(){
-    translate([4,4,-12])difference(){
+    translate([4,4,-18])difference(){
         hull(){
-            translate([0,0,6])cylinder(h=6, d=8);
-            translate([4,-4,0])cube([0.01,8,12]);
+            translate([0,0,12])cylinder(h=6, d=8);
+            translate([4,-4,0])cube([0.01,8,18]);
         }
-        translate([0,0,12])mirror([0,0,1])through(l=10,lb=1,lt=1,lh=7);
+        translate([0,0,18])mirror([0,0,1])through(l=10,lb=1,lt=10,lh=7);
     }
 }
 

shroud.scad

@@ -29,8 +29,8 @@ module through(l=7, lh=3.3, lt=1, lb=1){
 }
 
 module m3 (h=8, lt=1){
-    translate([0,0,-lt])cylinder(h, d=2.5); // tapped M3
-    //translate([0,0,-lt])cylinder(h, d=4); // rutex insert
+    //translate([0,0,-lt])cylinder(h, d=2.5); // tapped M3
+    translate([0,0,-lt])cylinder(h, d=4); // rutex insert
 }
 
 module mount(){